Contact Us   客
   服
   中
   心










商城 > IP 商城

    
14-Bit 1MSPS DAC in GSMC110nm 参考报价 75.000 K μm^2 1 MHz 110 nm  
MIC_DAC14 is compact and low power 14-bit digital-to-analog converter silicon IP. It features wide range input supply voltage from 1.7V to 5.6V. Its single-end output ranges from 0.1 to 0.9 of supply voltage. 概述
10-Bit 165 MSPS ADC in TSMC110nm 参考报价 210.000 μm^2 165 MHz 110 nm  
MIC_ADC10 is compact and low power 10-bit analog-to-digital converter silicon IP. This ADC uses 1.5b/stage pipelined architecture and it is optimized for low power Figure 1. BLOCK DIAGRAM and small area. 概述
Clock divider by 3 100 点 52.000 Gates 370 MHz 130 nm  
There are 2 types of circuits in digital logic world. One is combinational, and the other is sequential. The difference between them is that the latter one has storage (memory) while the former one does not. Thus, in contrast to combinational circuits, whose output depends only on the current values of its inputs, the output of sequential circuits depends not only on the current values of its inputs but also on the past values of them. Based on the characteristic of sequential circuits, we can build counters. In addition, we can further build clock dividers with the counters we designed 概述
SPI slave in mode 3 1000 点 256.000 Gates 285 MHz 130 nm  
The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it.The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions:The typical SPI bus architecture is designed as follows:When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line.With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively: 概述
SPI slave in mode 0 1000 点 274.000 Gates 243 MHz 130 nm  
The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it. The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions: The typical SPI bus architecture is designed as follows:   When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line. With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively:   概述
SPI slave in mode 1 1000 点 276.000 Gates 285 MHz 130 nm  
The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it. The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions: The typical SPI bus architecture is designed as follows: When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line. With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively:   概述
SPI slave in mode 2 1000 点 254.000 Gates 192 MHz 130 nm  
The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it. The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions: The typical SPI bus architecture is designed as follows: When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line. With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively:   概述
Asynchronous I2C Slave 999 点 578.000 Gates 100 MHz 130 nm  
Unlike Synchronous type I2C slave design need clock to work. This Asynchronous type don’t need base clock . It is very power saving in some application     Application :    - Power manager IC   - Sensor IC   - Software wakeup requirement system 概述
One Wire Communication 1200 点 1.500 K Gates 100 MHz 130 nm  
In some particular application, few pin count but still need chip to chip communication. This IP use one wire bi-direction (open drain) to communication. Just like UART , it is consist of one TX and one RX. User can define their own payload freedomly.   All devices are connecting through open-drain pull high bus. Every device can send data to others actively. Waveform                                 Application       - Analog IC debug      - MCU program port      - Low pin count IC 概述
10-bit 165 MSPS ADC IP in 130 nm 70000 点 210.000 K μm^2 165 MHz 130 nm  
UIP_ADC10_165M_166413 is an ultra-compact and very low power analog-to-digital converter (ADC) silicon IP. The 10-bit 165 MSPS ADC includes an internal custom bandgap voltage reference. It is capable of supplying bias currents to other parallel ADCs.   The ADC uses fully differential pipeline architecture with custom low-disturbance digital correction technique which allows single supply bus for both digital and analog. The ADC is designed for high dynamic performance for input frequencies up to Nyquist. This makes the IP perfectly suitable for video, imaging and communication appliances.   The IP is available in different metal options as well as deep N-well (DNW) option for SoC with high level of substrate noise. It consumes only 48mW at 165 MSPS operation and requires silicon area of 0.21 mm2. The IP does not require any external decoupling and is ideal for integration in mixed-signal systems. The output data of ADC is available in 2’s complement format.   UIP_ADC10_165M_166413 can be used in the following applications:   ‧Digital imaging ‧TV/Video ‧Wireless LAN ‧Rx communication channel ‧IOT 概述
微IP 价格 逻辑闸数 工作频率 工艺   评价

 4  5  6  7  8  9  10  11  12  13